Open Access Open Access  Restricted Access Subscription Access

Production of corundum boats and crucibles used for metal melting and material analysis by casting method


https://doi.org/10.17073/1683-4518-2024-2-42-47

Full Text:




Abstract

Technological features of producing corundum boats and crucibles used for metal melting and materials analysis by casting an aqueous slip in a plaster mould are presented. It is shown that to obtain high-density corundum ceramics by this method it is necessary to use aqueous slips with a maximum content of alumina up to 80 wt. %. The density of sintered products is significantly impacted by the initial size of alumina particles in the aqueous suspension. To increase the stability of the aqueous suspension and reduce its viscosity it is necessary to use a dispersing additive. The developed technology has produced corundum high-density and strong products in a form of boats and crucibles of different configurations and dimensions. Ill. 7. Ref. 11. Tab. 4.

About the Authors

Yu. K. Nepochatov
ХК ПАО «НЭВЗ-Союз»
Russian Federation


P. M. Pletnev
ФГБОУ ВО «Сибирский государственный университет путей сообщения»; ФГБОУ ВО «Новосибирский государственный аграрный университет»
Russian Federation


D. S. Tyulkin
ХК ПАО «НЭВЗ-Союз»
Russian Federation


References

1. Григорян, В. А. Материалы и защитные структуры для локального и индивидуального бронирования / В. А. Григорян, И. Ф. Кобылкин, В. М. Маринин, Е. Н. Чистяков ; под ред. В. А. Григоряна. ― М. : РадиоСофт, 2008. ― 406 с.

2. Garshin, A. P. Shock-resistant materials based on commercial grade ceramic: achievements and prospects for improving their ballistic efficiency / A. P. Garshin, V. I. Kulik, A. S. Nilov // Refract. Ind. Ceram. ― 2016. ― Vol. 57, № 2. ― Р. 207‒219. https://doi.org/10.1007/s11148-016-9955-0.

3. Мыльников, В. В. Анализ материалов и их свойств, применяемых для средств индивидуальной бронезащиты / В. В. Мыльников, А. А. Абросимов, И. Д. Романов, А. Д. Романов // Успехи современного естествознания. ― 2014. ― № 9-2. ― С. 143‒147.

4. Келина, И. Ю. Повышение баллистической эффективности корундовой керамики / И. Ю. Келина, Л. А. Чевыкалова, И. Л. Михальчик [и др.] // Материалы доклада ХХ Международной научно-технической конференции «Конструкции и технологии получения изделий из неметаллических материалов», Обнинск, 2013. ― C. 327‒329.

5. ГОСТ Р 50744‒95 «Бронеодежда. Классификация и общие технические требования».

6. Добровольский, А. Г. Шликерное литье / А. Г. Добровольский. ― М. : Металлургия, 1977. ― 240 с.

7. Гаршин, А. П. Материаловедение. Техническая керамика в машиностроении ; 2-е изд., испр. и доп. / А. П. Гаршин. ― М. : Юрайт, 2020. ― 296 с.

8. Nepochatov, Yu. K. Production of corundum boats and crucibles used for metal melting and material analysis by the casting method / Yu. K. Nepochatov, P. M. Pletnev, D. S. Tyul'kin // Refract. Ind. Ceram. ― 2022. ― Vol. 63, № 2. ― Р. 122‒125. https://doi.org/10.1007/s11148-022-00692-y.

9. Макаренко, В. В. Технологические особенности получения композиционного керамического материала методом литья : тез. докл. Международной конференции огнеупорщиков и металлургов (6‒7 апреля 2017 г., Москва) / В. В. Макаренко, Г. Д. Семченко, Д. А. Бражник, Е. Е. Старолат // Новые огнеупоры. ― 2017. ― № 3. ― С. 45, 46.

10. Пат. 1663916 Российская Федерация. Диспергатор керамического шликера для корундовой керамики / Бочаров В. А., Лисогорская М. Д., Лысогор Н. А., Харченко А. В., Горошков О. В., Воронин Ю. Л. ; заявл. 01.03.88 ; опубл. 23.10.92, Бюл. № 39.

11. Abramshe, R. Improving сeramic аrmor рerformance with better мaterials / R. Abramshe // Ceramic Industry. ― 2006. ― October issue (published by BNP Media, Troy, MI, USA).


Supplementary files

For citation: Nepochatov Y.K., Pletnev P.M., Tyulkin D.S. Production of corundum boats and crucibles used for metal melting and material analysis by casting method. NOVYE OGNEUPORY (NEW REFRACTORIES). 2024;(2):42-47. https://doi.org/10.17073/1683-4518-2024-2-42-47

Views: 79

Refbacks

  • There are currently no refbacks.


ISSN 1683-4518 (Print)